GD427 MK IV

GD427 MK IV
One of my first drives out - 8th September 2025 (St Ninian's Isle - Shetland)
Showing posts with label Handbrake. Show all posts
Showing posts with label Handbrake. Show all posts

Thursday, 9 March 2023

More Carpets & Handbrake Lever

After I got the fibreglass cut, and the rear carpet piping cut off, I was able to fit and glue the rear carpet, and both side carpets.  I have also fitted the edging around the door opening.  The door opening and the carpet sewing don't line up 100%, so I managed to manipulate what I could to get it as looking as good as I could.

The footwell carpets could then be laid in and holes cut in them for the safety harness eye bolts to pass through them.






I bolted in the handbrake bracket complete with handbrake lever.  This was spaced off slightly using washers on the top holes so there is room for your knuckles between the side of the car.

I put on the leather cover and also the stainless finisher around the base which neatens it up.


The leather cover will be rolled back and tied so that the hand grip is revealed.  I stuck the front footwell carpets down with some double sided velcro, so we will see how it manages to hold on through time, and if I ever need to remove them.

Thursday, 26 May 2016

Rear Brakes

I fitted the rear brake pads and connected up the handbrake cable.  I also replaced the bleed nipples with stainless ones.

I need to shorten the handbrake cable, but unless I can get a measurement from GD, then I will have to wait until I fit the body and handbrake lever.  This is due to the fact that I don't know the "zero" position of the lever mechanism.  I will contact Andy and see how they work it out...  I also swapped around my p-clip mount on the diff, since it clashed with the O/S cable.







Tuesday, 17 May 2016

Handbrake Cable Mount

I decided to make an additional mount to help guide the handbrake cable.  There is already a P-Clip under the brake pipe Tee piece, but I thought it would help having one on the diff.

The hole is a M12 x 1.5mm thread.  I started with a standard M12 x 1.75mm bolt (65mm long to get a long enough shank).  I cut off the threaded part and faced off the end of the bolt in the lathe.  I put on a 45 degree chamfer to assist the thread die.  I then threaded the shank.

I drilled a 4.2mm hole in the head end of the bolt and I tapped it to M5.

I put in place a 17mm P-clip and I will adjust the rotation once the cable is fully installed.








Friday, 13 May 2016

Rear End Work

The correct bolts for the driveshafts arrived, and have now been fitted.  




I have also finally fitted the flexible brake hoses to the rear callipers and clipped them to the upper wishbones.




The propshaft bolts have also been fitted.


I have fitted the callipers and discs, but still have to fit the pads.




I have also changed out the bolt for the handbrake anchor point so that the fitting is fully on the shank of the bolt and not threads.



I will be making a small bush for a p-clip to loosely hold the handbrake cable in position.  I will post up photos once made.  It is a M12 x 1.5mm thread, so not standard.  I am waiting on a thread die.


It's coming together.....




Thursday, 14 April 2016

Handbrake - Update

I have been thinking about the handbrake mechanism and how it works.

I decided to add in some bushes so that the stainless bolts could be tightened and still allow the mechanism to move smoothly.  I prefer to do it this way rather than rely on a nylon lock nut tweeked until it's "just right".

I turned down some stainless tubing (10mm O/D) to just thicker that the stainless plate (6mm).  I then drilled a 10.5mm hole in the stainless plate to allow clearance for the bush.

The bush is a little slack in the hole, but when tightened up fully, it rotates very smoothly.

I did this for both ends of the mechanism.



I have bolted up the end of the handbrake cable using a stainless bolt.  Once installed and set to the correct height, I have now bought a M8 bolt with a longer shank so that the handbrake cable end doesn't touch the threaded part of the bolt.




I mounted a rubber coated stainless p-clip on the rear brake tee-piece to help guide the handbrake cable.  I will place another p-clip on the differential to assist too.  The external sheath of the cable actually moves the handbrake mechanism so the route of the cable has to be kept neat and with sweeping bends to keep it all smooth.





Monday, 7 March 2016

Handbrake

I have been doing a few jobs lately, with quite a lot of thinking regarding fuel pipe runs and what fuel supply system I am going to use.

I thought that I would get a few things done while I am trying to decide.

I have drilled a few holes for mounting the stainless p clips and have tapped a M5 thread for the bolt.

I will post up some photos when I am assembling the p clips since showing a hole isn't too telling!

I have been trying to work out how the handbrake mechanism is designed to function, and I have decided to modify the lever that was provided with the kit so that it fits above the chassis mount.  Dale's car has the lever above the mount, but the one supplied with my kit couldn't fit.  I have since ground the lever down to fit on the existing mount to match what I think is correct.





Saturday, 30 January 2016

Finished Brake Lines

I have altered the right rear brake line to accommodate the handbrake cable if it requires to be changed out in the future (shouldn't ever need to?).

I think this gives enough room for everything required, and it still neat enough not to get in any things way.



I still need to finally bolt the tee piece into position using an M6 bolt, but I will also put on a P-clip to hold the main handbrake cable that runs from the handbrake lever.

The handbrake cable is too long so I will have to investigate how short I need to cut it.  I have seen some people using splice crimps, but I am going to look into remaking the end that goes onto the calliper itself.  I'll keep you posted.